Modelling the effect of changing precipitation inputs on deep soil water utilization          下载免费PDF全文

Ji Qi  Daniel Markewitz  David Radcliffe 《水文研究》2018,32(5):672-686

Forests in the Southeastern United States are predicted to experience future changes in seasonal patterns of precipitation inputs as well as more variable precipitation events. These climate change‐induced alterations could increase drought and lower soil water availability. Drought could alter rooting patterns and increase the importance of deep roots that access subsurface water resources. To address plant response to drought in both deep rooting and soil water utilization as well as soil drainage, we utilize a throughfall reduction experiment in a loblolly pine plantation of the Southeastern United States to calibrate and validate a hydrological model. The model was accurately calibrated against field measured soil moisture data under ambient rainfall and validated using 30% throughfall reduction data. Using this model, we then tested these scenarios: (a) evenly reduced precipitation; (b) less precipitation in summer, more in winter; (c) same total amount of precipitation with less frequent but heavier storms; and (d) shallower rooting depth under the above 3 scenarios. When less precipitation was received, drainage decreased proportionally much faster than evapotranspiration implying plants will acquire water first to the detriment of drainage. When precipitation was reduced by more than 30%, plants relied on stored soil water to satisfy evapotranspiration suggesting 30% may be a threshold that if sustained over the long term would deplete plant available soil water. Under the third scenario, evapotranspiration and drainage decreased, whereas surface run‐off increased. Changes in root biomass measured before and 4 years after the throughfall reduction experiment were not detected among treatments. Model simulations, however, indicated gains in evapotranspiration with deeper roots under evenly reduced precipitation and seasonal precipitation redistribution scenarios but not when precipitation frequency was adjusted. Deep soil and deep rooting can provide an important buffer capacity when precipitation alone cannot satisfy the evapotranspirational demand of forests. How this buffering capacity will persist in the face of changing precipitation inputs, however, will depend less on seasonal redistribution than on the magnitude of reductions and changes in rainfall frequency.  相似文献   

顾及地类转换差异的城市空间扩展元胞自动机模型及应用研究     

于明明  曾永年 《地球信息科学学报》2018,20(1):48-56

元胞自动机模型已经成为城市空间扩展模拟研究的重要方法之一,并得到广泛应用。然而,现有的城市扩展元胞自动机模型仍存在不足。由于元胞状态设置较为简单,从而使模型转换规则中对不同用地类型向城市用地转换的差异与强度考虑不够。基于此本文在元胞自动机模型的框架下,设计了多元结构的元胞状态及转换规则,提出了顾及地类转换差异与强度的城市扩展元胞自动机模型。在计算非城市用地向城市用地转换的转换概率时,该模型考虑了3个方面的概率：① 地形地貌、经济发展等城市发展的驱动因素对城市用地扩展的影响概率,该概率采用logistics方法进行计算;② 邻域元胞的用地类型对中心元胞转换概率的影响,该概率采用扩展摩尔型方法进行计算;③ 不同类型的非城市用地（本研究中包括耕地、林地和裸地3种类型）向城市用地转换的强度,该概率由模拟基期土地利用数据与目标年份土地利用数据的叠加,得出不同类型的非城市用地在此时间段内向城市用地转换的规模,进而确定不同类型的非城市用地向城市用地转换的强度。最后,将以上3种概率的乘积作为元胞转换的概率。通过转换概率与转换阈值的对比判断中心元胞是否在下一个阶段转换为城市用地。经过迭代计算,不断增加城市用地元胞的数量。当模拟城市用地的结果与目标年份的城市用地规模差值在一定的范围内时停止模拟,得出最终结果。模型构建完成后,本文以长株潭城市群核心区为例进行了模拟实验。以2001年该地区的土地利用数据为基期数据,模拟2010年该地区的城市用地规模和空间分布。研究结果表明,根据本文提出的模型模拟的城市扩展结果与真实数据相比具有较高的一致性。模拟结果正确率达到68.66%,比基于传统logistics回归的元胞自动机模型的模拟精度提高了4.25%,Kappa系数为0.675。该模型较好地模拟了长株潭城市群核心区城市扩展,在城市空间扩展模拟中具有较好的适应性与有效性。  相似文献   

弧形海岸裂流的数值模拟研究   总被引：3，自引：0，他引：3  

汪鸿  朱首贤  李训强  张文静  聂屿 《海洋学报(英文版)》2018,37(3):21-30

弧形海岸波浪产生的裂流严重危害人类活动，但是目前对其特征缺乏充分认识。本文对Haller物理模型实验和三亚大东海的数值模拟表明FUNWAVE模式具有较好的裂流模拟能力。基于该模式进行了多种弧形海岸条件的裂流数值模拟，给出裂流的一些特征：（1）海岸弯曲度增大，裂流增强；（2）海岸坡度对裂流有比较大的影响，太陡或太平缓的海岸不利于形成裂流；（3）海岸尺寸减小，裂流减弱；（4）波高和波周期增大，裂流增强，但是对于某些海岸而言，0.4m波高可能就存在危害比较大的裂流。  相似文献   

Three-dimensional finite element simulation of fracture propagation in rock specimens with pre-existing fissure(s) under compression and their strength analysis     

Ramin Pakzad  Shanyong Wang  Scott W. Sloan 《国际地质力学数值与分析法杂志》2020,44(10):1472-1494

A FORTRAN program, consistent with the commercially available finite element (FE) code ABAQUS, is developed based on a three-dimensional (3D) linear elastic brittle damage constitutive model with two damage criteria. To consider the heterogeneity of rock, the developed FORTRAN program is used to set the stiffness and strength properties of each element of the FE model following a Weibull distribution function. The reliability of the program is assessed against available experimental results for granite cylindrical specimens with a throughgoing, flat and inclined fissure. The calibration procedure of the material parameters is explained in detail, and it is shown that the compressive to tensile strength ratio can have a substantial influence on the failure response of the specimens. Numerical simulations are conducted for models with different levels of heterogeneity. The results show a smaller load bearing capacity for models with less homogeneity, representing gradual coalescence of fully damaged elements forming throughout the models during loading. The maximum load bearing capacity is studied for various combinations of inclination angles of two centrally aligned, throughgoing and flat fissures of equal length embedded in cylindrical models under uniaxial and multiaxial loading conditions. The key role of the compressive to tensile strength ratio is highlighted by repeating certain simulations with a lower compressive to tensile strength ratio. It is proven that the peak loads of the rock models with sufficiently small compressive to tensile strength ratios containing two throughgoing fissures of equal length are similar, provided that the minimum inclination angles of the models are the same. The results are presented and discussed with respect to the existing experimental findings in the literature, suggesting that the numerical model applied in this study can provide useful insight into the failure behaviour of rock-like materials.  相似文献   

Implementation of a coupled plastic damage distinct lattice spring model for dynamic crack propagation in geomaterials          下载免费PDF全文

Chao Jiang  Gao‐Feng Zhao 《国际地质力学数值与分析法杂志》2018,42(4):674-693

This paper studies dynamic crack propagation by employing the distinct lattice spring model (DLSM) and 3‐dimensional (3D) printing technique. A damage‐plasticity model was developed and implemented in a 2D DLSM. Applicability of the damage‐plasticity DLSM was verified against analytical elastic solutions and experimental results for crack propagation. As a physical analogy, dynamic fracturing tests were conducted on 3D printed specimens using the split Hopkinson pressure bar. The dynamic stress intensity factors were recorded, and crack paths were captured by a high‐speed camera. A parametric study was conducted to find the influences of the parameters on cracking behaviors, including initial and peak fracture toughness, crack speed, and crack patterns. Finally, selection of parameters for the damage‐plasticity model was determined through the comparison of numerical predictions and the experimentally observed cracking features.  相似文献   

铜藻(Sargassum horneri)在营养限制胁迫后对NH₄-N的超补偿吸收研究     

李大鹏  马增岭  李慧  丁刚  辛美丽  吴海一  郭文 《海洋与湖沼》2018,49(4):904-909

以经济马尾藻铜藻(Sargassum horneri)为研究材料,研究了其在营养限制胁迫后对NH_4-N的超补偿吸收情况。实验分营养限制和恢复营养两个阶段进行,每个阶段均设置饥饿处理组、饱和处理组和正常对照组。铜藻在低营养限制胁迫(饥饿)下培养10天后,恢复营养盐培养3天,分别采用次溴酸盐氧化法和锌镉还原法测定培养液中的NH_4-N和NO_3-N的浓度。本文研究发现,饥饿处理组中铜藻吸收氨氮的速率远高于正常对照组和饱和处理组,在恢复培养第一天时,饥饿处理组对NH_4-N的吸收速率最高为14.94μmol/(g·h),与正常对照组及饱和处理组间差异显著。在恢复培养的后两天,三个处理组中铜藻对NH_4-N的吸收速率差异慢慢变小,直至最后几乎相同。三组对NO_3-N没有表现出较高的吸收,最高仅为6.15μmol/(g·h),结果表明:氮源包括NH_4-N和NO_3-N时,铜藻优先选择吸收NH_4-N。实验后称重测定生长速率:对照组、饥饿处理组和饱和组生长率(SGR)分别为8.48%、8.86%、8.01%,ANOVA方差分析表明,三者存在显著差异(P=0.0320.05),从而证实了铜藻也存在超补偿生长的现象。  相似文献   

典型深街谷内树木空间配置对行人呼吸高度处气流的影响     

林定  申小云  朱勇兵  陈崇成 《地球信息科学学报》2018,20(9):1235-1243

为揭示树木的不同空间配植方案对行人呼吸高度气流的影响,本文将树木视为均匀多孔介质,通过附加源项法从空气动力学角度用CFD模拟了H/W=2的典型深街谷几何内4种树木配植情景,实验表明,不同空间配置下树木对街谷内行人呼吸高度处局地气流的影响强弱在空间分布模式上差异悬殊：① 均匀种植的树木对街谷内行人呼吸高度的气流起到阻碍作用,不均匀种植则有效提升街谷的整体流速。4种空间配植方案下树木对气流的影响程度不同,阻碍作用从大到小的顺序为均匀间距8 m（Spa8m）>均匀间距6 m（Spa6m）>均匀间距20 m（Spa20m）>不均匀配植（Non-uniform）;对应的平均气流增强指标顺序为$\bar{D}_{spa8}$（-19.31%）<$\bar{D}_{spa6}$（-16.14%）<$\bar{D}_{spa20}$（-10.73%）<$\bar{D}_{non-uniform}$（1.25%）。② 对比不均匀和均匀的种植方案,不均匀植树的街谷内部行人呼吸高度的气流流速比其对照案例（均匀植树Spa8m方案）整体增强了106.49%。街谷中部不种树,在街谷两端配置树木并预留足够的自由空间的不均匀植树方案,能够让角涡渗入街谷中部,促使街谷内部的垂直漩涡和两端的水平角涡运动,增强湍流和垂直交换,有效减少了街道两端“风口效应”和街道中部“风影效应”的区域,改善了整个街谷行人呼吸平面的风环境。④ 合理空间配置的树木能够改善街谷内部的行人风环境。街谷内行人呼吸高度处的气流对局地条件很敏感,树木的局部配置（空间簇集、密度）将引起强烈的空间变化。在既有城市建筑布局条件下,如何通过谨慎的景观设计,利用树木等城市绿化措施有效地改善城市的行人风环境,缓解污染扩散、疾病传播等问题,本文的方法可提供一定的参考。  相似文献   

Properties of geogrid-reinforced marine slope due to the groundwater level changes     

Ramin Vali  Jie Li  Gholamreza Shams  Pieter van Gelder 《Marine Georesources & Geotechnology》2018,36(6):735-748

Evaluation of slope stability, especially in the absence of a proper bed such as marine soils, is one of the most important issues in geotechnical engineering. Using geogrid layers to enhance the strength and stability of embankments is regarded as a commendable stabilization method. On the other hand, groundwater level erratically fluctuates in coastal areas. Therefore, the aim of this research is to study the effects of groundwater level changes on stability of a geogrid-reinforced slope on loose marine soils in Qeshm Island, Iran. At first, geotechnical properties of the site were obtained by comprehensive series of geotechnical laboratory and in situ tests. Then, by simultaneous changes of groundwater level and several parameters such as embankment slope, loading, geogrid length, geogrid number, and tensile strength of geogrid, different characteristics such as embankment safety factor (SF), vertical and horizontal displacements at embankment top and embankment base were studied. It was observed that groundwater level had significant effects on behavior of the embankment. For most of the observations, by decreasing the groundwater level, the displacements decreased and consequently safety factor increased. Increasing the length, number, and tensile strength of geogrid led to the reduction of displacements and an increase in the safety factor.  相似文献   

Bearing capacity of offshore umbrella suction anchor foundation in silty soil under varying loading modes     

Qi Yang  Guanglai Pan  Quandi Wang 《Marine Georesources & Geotechnology》2018,36(7):781-794

Considering the current disadvantages of present offshore wind turbine foundations, a novel anchor foundation with skirt and branches is proposed, called offshore umbrella suction anchor foundation (USAF). A series of experiments and numerical simulations were performed to explore the bearing capacity of the USAF under various kinds of loading modes. The bearing characteristics and the anchor–soil interactions are described in detail for horizontal static loading, horizontal cyclic loading, and an antidrawing (pullout) test in silty soil. In the static loading test, the load–deflection of the anchor under step loading was analyzed and the normalized curve of the load–deflection was obtained to determine the ultimate horizontal bearing capacity of the anchor under normal working conditions. Under horizontal cyclic loading, the relationship between the plastic cumulative deformation and cyclic number was determined. In addition, the responses of USAF were investigated for a low wave frequency and storm surges. In the drawing test, it was found that a “segmentation phenomenon” occurred during the test. Moreover, a method to identify the maximum antidrawing load of USAF was provided based on dynamic mechanics. The numerical results show that the use of anchor branches and skirt can enhance the bearing performance of USAF to a certain degree. However, the anchor branch has a slight positive influence on the bearing performance improvement. The USAF is not only similar to a stiff short pile, but a rotation occurs. The failure envelope under composite loading (V-M) was obtained and the changes associated with changes in the aspect ratio of the internal compartment were clarified.  相似文献   

基于圆柱多段拟合的隧道中轴线提取方法研究     

荆海峰  李广云  王力  杨文锋 《大地测量与地球动力学》2018,38(2):211-215

提出基于圆柱多段拟合的隧道中轴线提取方法。首先对隧道点云数据进行预处理，并将点云按隧道走向分成不同区段；然后对各区段依据轴线与表面点云法线垂直关系，提取精度较低的中轴线；最后对各区段利用圆柱多段拟合，提取精度较高的中轴线。实验表明，隧道中轴线的提取在一定的采样区间具有较高的稳定性，对直线和弯曲的圆形隧道有良好的适用性，算法可靠，精度较高。  相似文献